This is the first standalone software that can change IMEI number of a Nokia DCT4 phones to any digit without UEM change and change ESN on DCT4 Phones without UEM Change.

This software allows you to:
- Change IMEI on DCT4 phones without opening the phone (UEM Change)
About DCT4 Direct Software:
- Works on Window XP
- Future updates and support
- Real USB data transfer between PC and Phone
- Best Quality phone Cables and Software

How its works:
On all Nokia DCT4 phones the important security data for the IMEI and ESN is stored on a special, note rewritable chip inside the phone: the UEM chip. This chips characteristic is that it is only one time programmable (OTP) and that the data inside cannot be rewritten. Because of this, until now it was only possible, to change the IMEI/ESN if you change this UEM chip. Since this task requires a lot of time and effort, alot of customers were looking for a easier solution, without the need to open the phone and change some components inside. And after some time finally somebody created a tool that was able to do all that operations without changing the UEM chip: the DCT4 DIRECT Box. THis software is using a special techic in order to make it posssible to change the IMEI/ESN without changing any data on the UEM chip it self. This task is done by editing the MCU Firmware inside the phone and writing the desired IMEI/ESN data to the FLASH, not to the UEM chip, this procedure is also known as FLASH PATCHING. After the phone has been updated with the patched flash data by the DCT4 DIRECT BOX the phone will have the new IMEI/ESN number and all simlock data rebuilded as well. This might sound a little bit complicated now, but in fact the user is not affected in any way by this procedure. All the user need to do is to type the desired IMEI/ESN number into a field and then just press one button for starting the IMEI/ESN change. IMEI/ESN change on DCT4 phones is really easy now.

Support phone models:
DCT4 Direct (v1.0.0.32):

• NHM-7 - 8310, v 6.20
• RH-19 - 3100, v 5.91
• NHL-6 - 6800, v 3.14
• RH-9 - 3510i, v 5.35
• RM-17 - 7260, v 3.36
• NEM-1 - 3300, v 4.62
• NPL-2 - 6100, v 5.80
• RH-23 - 7200, v 4.26
• NHL-4J - 7250, v 3.62
• NPE-4 - 6310, v 5.10
• NHL-4 - 7210, v 5.63
• NPL-1 - 6310i, v 7.00
• RH-37 - 3220, v 3.60
• RM-37 - 6610i, v 4.10
• NHM-8 - 3510, v 5.02
• RH-30 - 3200, v 5.29
• NHL-4JX - 7250i, v 5.30
• NKC-1 - 2270, v 9.07
• NPC-1 - 3320, v 4.00
• NPW-1PA - 3361*, v 3.06
• RH-17R - 2280, v F175V0500.nep
• DTE-1 - D211*, v 4.01
• RH-18 - 1100*, v 5.62
• NPM-10 - 3595, v 8.18
• NKC-1 - 1220, v 9.07
• NPD-1AW - 3585, v B100V0557.nep
• RH-44 - 3586, v D100V0112.nep
• RH-3 - 2285, v G101V0801.nep
• NPM-8 - 3590, v 7.64
• RM-12 - 7710, v Vp2.200
• RA-2 - 9500, v 3.35.2
• RH-38 - 1100a*, v 5.62
• NHL-9 - 6820a, V 4.25
• RAE-6 - 9300, v 3.06
• RH-48 - 3105, v J175V0300.nep
• NPL-3 - 6200, v 4.22
• RH-27 - 6225, v H190V0800.nep
• RH-50 - 3100b, v 4.03

Note:
The Supported Phones above marked with Star (*) sign do not operate properly with this version. Do not use them. In case you do and have a dead phone, just reflash the MCU to repair it(1100 - MCU+PPM).

IMPORTANT:

• Please note that the DCT4 DIRECT BOX cannot work with phones that:
  - Have bad UEM data (30 sec off problem)
  - Don't have any UEM data at all (?????????????? IMEI/ESN)
  - Have SOftware/Hardware problems
• Please always check if phone is in full working condition before starting the IMEI/ESN change procedure.
• If you want to bring the phone back to it's original state, then you only need to flash the phone with origitnal MCU software. After MUC software update the patch will be erased and the phone will operate as before.

Package Contains :

• DCT4 DIRECT USB BOX
• USB power cables
• Cd with DCT4 Direct Software
• Complete Set Cable
  NK1100, NK2280, NK2650, NK3200, NK3220, NK3230, NK3300, NK3310, NK3320, NK3360, NK3510, NK3650, NK5100, NK5140, NK6100, NK6101, NK6170, NK6230, NK6260, NK6340, NK6600, NK6620, NK6650, NK6800, NK6820, NK7200, NK7210, NK7260, NK7280, NK7600, NK7610, NK7650, NK7710, NK8310, NK8800, NK8850, NK8910, NK9300, NK9500, USB cable

Email this to a friend	* means required information
*Name of your friend
*E-mail of your friend
*Your Name
*Your Message	DCT4 DIRECT BOX - This is the first standalone software that can change IMEI number of Nokia DCT4 phones to any digit without UEM change, and also change ESN on DCT4 Phones without changing the UEM.